MINERAL / GRAIN PATTERN DECORATIVE PLASTER (1.5 mm)
Product Description:
White cement-based, polymer and fiber-added, water-repellent, mineral / grain pattern decorative facade coating.
It is suitable for TS 7847 standards.
Public Works Pos No: 04.476/A
Areas of Use:
As the last layer coating material in sheathing systems,
It is used as a decorative coating on interior and exterior facades.
Features:
It is water repellent and is not affected by water.
It is resistant to external effects and frost.
It has good adherence and high strength.
It does not crack thanks to its special filling size, polymer and fiber.
It is flexible, easy to apply.
It can be painted over after it dries.
It has the ability to breathe thanks to its vapor permeability.
Technical Specifications:
Appearance: White Powder
Dry Unit Weight: 1.6 ± 0.2 kg / m³
Application Temperature: + 5ºC to + 35ºC
Application Thickness: 1.5 mm
Water Mixing Ratio: 6.0-7.0 Liter / Bag
Rest Time of Mortar: 2-3 min.
Pot Life: 1-2 hours
Working Time: 20-30 min.
Drying Time: 24 hours.
Compressive Strength: ≥ 3 N / mm²
Flexural Strength: ≥ 1.5 N / mm²
Temperature Resistance: -25 C to + 80 C
The above values are given for +23 ºC and 50% relative humidity.
Dry Film Thickness: E5
By Grain Size: S4
Water Vapor Transfer Rate: V1
Water Transfer Rate: W2
Crack Covering Feature: A0
Carbon Dioxide Permeability: C0
Resistance to Mold Growth: K2
The above values are classified according to TS EN 1062-1.
Pre-Application Preparation:
Care must be taken that the application surface is cured and solid.
The application surface should be free from materials such as dust, oil, paint that prevent adhesion.
Sub-surfaces such as cracked plasters and weak surfaces that are not strong enough to carry the application should be cleaned from the application surface.
The floors that require repair should be repaired with special repair mortars at least 3-4 days before the adhesive is applied.
The application surface should be wetted and care should be taken to keep it moist.
If the surface is very absorbent, it is recommended to use a primer on the surface.
Application:
25 kg Alldeco M6 1.5 mm Decorative Plaster is poured into a container filled with approximately 6.0-7.0 liters of water and mixed with a low speed mixer or trowel until a smooth mixture is obtained.
During the mixture, any additives not specified in the application instructions should not be added.
The prepared mortar is 2-3 minutes. Let it rest for maturity and again 1-2 minutes. It should be mixed until it becomes homogeneous.
The mixture in the pot should be consumed within about 1 hour.
Decorative plaster should be applied to the surface with a steel trowel and spread over the entire surface in equal thickness.
Application thickness should be adjusted according to the largest aggregate.
Before the plaster dries, the plaster is patterned by making circular movements with a plastic trowel.
After drying, it can be painted with an optional, solvent-free exterior paint.
Warnings:
It should be applied without interruption on wide facades and with sufficient personnel.
At the points that require a compulsory finish on the facade, the borders should be determined with a protective tape and the application should be made.
During the application of the final coatings, it should be prevented from drying quickly due to adverse weather conditions.
In order to prevent rapid and unhealthy drying, the plastered surfaces should be protected from direct sunlight, heavy weather conditions such as strong wind, hail and frost.
In order to achieve the expected and desired long-term performance of the product, after the completion of the entire application, as soon as possible (3-7 days depending on the drying time of the product applied), the application with a suitable coating (paint etc.) or it needs to be coated.
Consumption: Average 2.50-3.00 kg / m²
The amount of consumption is the values calculated theoretically in the laboratory environment; We recommend that consumption control sample application be made before the application.
Packing: 25 kg craft bags.
Storage and Shelf Life:
It should be stored in its unopened original package, in a cool and dry environment, protected from frost. For short term storage, maximum 3 palettes should be placed on top of each other and the shipment should be made on a first in, first out system.
Palettes should not be stacked on top of each other during long term storage.
It is 12 months from the date of production under suitable storage conditions.
Opened packages should be stored under appropriate storage conditions and used within one week.
Safety Advices:
For more detailed information, please refer to the Safety Data Sheet.
Responsibility:
The application instructions and technical values given in this technical document are based entirely on our scientific and practical knowledge. These values may vary depending on the ambient conditions. Allmax Construction Chemicals reserves the right to make changes in products in line with technological developments. Allmax Yapı Kimyasalları cannot be held responsible for the results that may arise out of written recommendations regarding where and how the product will be used and / or due to incorrect use. Therefore, when using Allmax Construction Chemicals products, make sure that you use the right product in the right place. Allmax Construction Chemicals is only responsible for the quality of the product.
