FLEX TILE-CERAMIC ADHESIVE MORTAR-WHITE
Product Description:
It is a white cement-based, flexible tile-ceramic adhesive mortar with reduced slip feature, long working time.
It is suitable for TS EN 12004 I C1TE class.
C: Cement based
1: Normal hardening (Standard performance) T: Reduced slip feature
E: Extended working time
Public Works Pos No: 04.013/1
Areas of Use:
Indoor and outdoor,
On horizontal and vertical surfaces,
Bonding of coating materials such as floor and wall ceramics, glass bricks, glass mosaic, decorative brick
Places with high density of people (places such as shopping malls, hospitals, schools)
In wet areas,
It is used in places where sudden temperature changes are high.
The surface must be notched or primed with Primerfix 101, Smooth Surface Primer before existing ceramic bonding applications.
Features:
It has high adhesion strength.
It has a long working time and resistance to heat difference.
It is flexible.
It is easy to apply.
It is resistant to water, moisture and frost.
It is durable and long-lasting.
It does not slip in vertical applications.
It allows laying from top to bottom.
Technical Specifications:
Appearance: White Powder
Application Temperature: + 5ºC to + 35ºC
Water Mixing Ratio: 6,5-8,0 Liter / Bag
Rest Time of Mortar: 5-10 min.
Pot Life: 1-2 hours
Slip: ≤ 0.5 mm
Open Time: ~ 30 min.
Ready to Use: On the wall: 8 hrs. Floor: 24 hrs.
Adhesion Strength: ≥ 0.5 N / mm²
Reaction to Fire: A1
Temperature Resistance: -25 C to + 80 C
The above values are given for +23 ºC and 50% relative humidity.
Pre-Application Preparation:
Must be taken care that the application surface is cured and solid.
The application surface should be free of substances that prevent adhesion such as dust, oil, paint.
Sub-surfaces such as cracked plasters and weak surfaces that are not strong enough to carry the application should be cleaned from the application surface.
The floors that require repair should be repaired with special repair mortars at least 3-4 days before the adhesive is applied.
The application surface should be wetted and care should be taken to keep it moist.
If the surface is very absorbent, it is recommended to use a primer on the surface.
Application:
25 kg of Alfix Flex White, Flex Tile-Ceramic Adhesive Mortar is poured into a container filled with approximately 6.5-8.0 liters of water and mixed with a low-speed mixer or trowel until a lump-free mixture is obtained. During the mixture, any additives not specified in the application instructions should not be added. The prepared mortar is 5-10 minutes. let it rest for maturation and again 1-2 minutes. It should be mixed until it becomes homogeneous. In-pot mixture should be consumed within 1-2 hours. The prepared mortar is spread on the surface with a notched trowel with the appropriate tooth size.
On the combed mortar, coating materials such as tile-ceramic are applied for 20-30 minutes. (This period may vary depending on the ambient conditions of the application).
Adhesion should not be done on the expired mortar, the mortar should be scraped off the surface, and a new mortar should be applied again. With the help of a rubber hammer, the coating materials are tampered with and it is ensured to settle and stick well. In outdoor applications, it can be mixed with Allmax Latex to provide a stronger adhesion. Grouting should be done after 8 hours on the wall and 1 day on the floor.
Warnings:
Avoid application at temperatures below + 5ºC and above + 35ºC.
Newly completed applications should be protected against adverse weather effects such as direct sunlight, excessive air flow, high air temperature (above + 35ºC), rain and frost in the first days.
Avoid direct contact with water within the first 24 hours of the completed application.
Never add powder and water to the expired or crusted mortar in the container, discard the mortar.
Wash all tools and application equipment with clean water immediately after use.
Consumption: 3-5 kg / m²
The amount of consumption is the values calculated theoretically in the laboratory environment; We recommend that consumption control sample application be carried out before the application.
Packing: 25 kg craft bags.
Storage and Shelf Life:
It should be stored in its unopened original package, in a cool and dry environment, protected from frost. For short term storage, maximum 2 palettes should be placed on top of each other and the shipment should be made on a first in, first out system.
Palettes should not be stacked on top of each other during long term storage.
It is 12 months from the date of production under suitable storage conditions.
Opened packages should be stored under appropriate storage conditions and used within one week.
Safety Advices:
For more detailed information, please refer to the Safety Data Sheet.
Responsibility:
The application instructions and technical values given in this technical document are based entirely on our scientific and practical knowledge. These values may vary depending on the ambient conditions. Allmax Construction Chemicals reserves the right to make changes in products in line with technological developments. Allmax Yapı Kimyasalları cannot be held responsible for the results that may arise out of written recommendations regarding where and how the product will be used and / or due to incorrect use. Therefore, when using Allmax Construction Chemicals products, make sure that you use the right product in the right place. Allmax Construction Chemicals is only responsible for the quality of the product.