Repair and Strengthening Products
TAMİRES R8 GR
Technical Data Sheet Material Safety Form

CONSTRUCTIONAL REPAIR MORTARS

 Product Description:

Tamires R8 TX: Cement based, single component, polymer and fiber reinforced, thixotropic structural repair mortar.

 It is suitable for TS EN 1504-3 I R4 class

 Public Works Pos No: 04.613/3B

 Tamires R8 FL: Cement based, single component, polymer and fiber reinforced, non-decomposing, flowing, structural repair mortar.

 It is suitable for TS EN 1504-3 I R4 class

 Public Works Pos No: 04.613/3C

 Tamires R8 GR: It is a cement based, one component, polymer reinforced, self-compacting grout mortar.

 It is suitable  for TS EN 1504-3 I R4 class

 Public Works Pos No: 04.613/3C

 Areas of Use:

TAMİRES

R8 TX

R8 FL

R8 GR

Supporting Column, Beam and Curtain Repairs

x

x

 

Flooring and Plate Repairs

x

x

 

Repairing Spacers

x

 

 

Port, Pier and Water Structures Repairs

x

x

 

Corrosion Repairs

x

x

 

Core, Tij etc. Filling the Gaps

x

 

 

Pre-Insulation Repairs (Chamfer and Segradation)

x

 

 

In the Assembly of Prefabricated Building Elements

 

 

x

Fixing Steel Columns to the Foundation

 

 

x

Application Type

Molded Application

 

x

x

Trowel Application

 

 

 Features:

TAMİRES

R8 TX

R8 FL

R8 GR

High Adherence

x

x

x

High Pressure Strength

x

x

x

Thixotropic Property

x

 

 

Fluid Feature

 

x

x

Resistance to Freezing - Thawing Cycle

x

x

 x

Resistance to Chlorine and Sulphate Attacks

x

x

x

Resistance to Oils

x

x

x

Resistance to Water and Bad Weather Conditions

x

x

x

  

Technical Spesifications:

TAMİRES

R8 TX

R8 FL

R8 GR

Compressive Strength

TS EN 12190

 (N / mm²)

1 day

> 20

> 20

> 20

7 days

> 50

> 50

> 50

28 days

> 60

> 60

> 60

Flexural Strength

TS EN 196-1

(N / mm²) (28 Days)

> 7

> 7

> 7

Adhesion Strength to Concrete TS EN 1542

(N / mm²) (28 Days)

> 2

> 2

> 2

Elasticity Module Flexural Strength TS EN 13412 (GPa) (28 Days)

> 20

> 20

> 20

Capillary Water Absorption TS EN 13057 (kg / m²h0,5)

≤ 0,5

≤ 0,5

≤ 0,5

Application Thickness (mm)

10-40

10-40

10-40

Floor Temperature to be Applied

+5ºC - +30ºC 

Service Temperature

-20ºC
+400ºC

-20ºC
+400ºC

-20ºC
+400ºC

Usage Time (+ 20ºC)

30 min.

30 min.

40 min.

Ready to Use (+ 20 C)

24 hours

24 hours

24 hours

Full Curing Time (+ 20ºC)

28
days

28
days

28
days

The above values​​are given for +23 ºC and 50% relative humidity. These values ​​may vary depending on the application temperature.

 

Pre-Application Preparation:

Care should be taken to ensure that the cement-based surfaces of the buildings to be repaired are solid, bearing, dust-free and clean. Any kind of oil, grease etc. that will weaken the adherence of the surface. It should be thoroughly cleaned of residues. The edges of the surface created by breaking should be cut as perpendicular as possible, the rust on the reinforcement should be removed, and new reinforcement should be added if necessary. If there is water current on the surface, it should be drained or closed with a suitable plug. The application surface should be saturated with water, but there should be no free water on the surface.

 

Water Mixing Ratio:

Tamires R8 TX/FL/GR

1 Kg. for powder

25 Kg. for bag

Mixing Water Amount

0,14-0,16 liter

3,5-4,0 liter

 

Application:

Trowel Application: The prepared mortar is applied to the surface with a trowel or spraying in a single layer of 10-40 mm. In thicker applications, the second layer is applied in the same way after the first layer has dried on the maximum application thickness of the product. In cases where a smooth surface finish is desired, the mortar is expected to absorb its water and the plaster is sprinkled on the mortar that has been pulled with a brush, and the surface is finished with a steel or wooden trowel.

 

 

 

 

 

Mold Application: It should be poured continuously from one side of the mold in accordance with the maximum application conditions of the product. Thicker applications can be applied in 2 or 3 layers. Bilateral casting should be avoided. In order to ensure that all the gaps in the mold are filled, it should be placed using a steel wire with a hook end. After the application, molds should not be taken before 18-24 hours. Large surfaces open to atmosphere should be protected against rapid evaporation.

 Warnings:

Avoid application at temperatures below + 5ºC and above + 35ºC. Newly completed applications should be protected against adverse weather effects such as direct sunlight, excessive air flow, high air temperature (above + 35ºC), rain and frost in the first days. Avoid direct contact with water within the first 24 hours of the completed application. Never add powder and water to the expired or crusted mortar in the container, discard the mortar. Wash all tools and application equipment with clean water immediately after use.

 Consumption: It is 19-21 kg / m2 powder product for 10 mm thickness.

The amount of consumption is the values ​​calculated theoretically in the laboratory environment; We recommend that consumption control sample application be made before the application.

Packing: 25 kg craft bags.

Storage and Shelf Life:

It should be stored in its unopened original package, in a cool and dry environment, protected from frost. For short term storage, maximum 3 palettes should be placed on top of each other and the shipment should be made on a first in, first out system.

Palettes should not be stacked on top of each other during long term storage.

It is 12 months from the date of production under suitable storage conditions.

Opened packages should be stored under appropriate storage conditions and used within one week.

Safety Advices:

For more detailed information, please refer to the Safety Data Sheet.

 Responsibility:
 The application instructions and technical values ​​given in this technical document are based entirely on our scientific and practical knowledge. These values ​​may vary depending on the ambient conditions. Allmax Construction Chemicals reserves the right to make changes in products in line with technological developments. Allmax Yapı Kimyasalları cannot be held responsible for the results that may arise out of written recommendations regarding where and how the product will be used and / or due to incorrect use. Therefore, when using Allmax Construction Chemicals products, make sure that you use the right product in the right place. Allmax Construction Chemicals is only responsible for the quality of the product.